What is the difference between rg59 and rg6 connectors

Search In. Existing user? Sign in anonymously. Sign in to follow this Followers 0. Recommended Posts. SecurityNub 0. Posted November 22, Share this post Link to post Share on other sites.

From my experience RG6 and RG59 are two different cables. They are also much easier to install as they are often merged with a power cable to reduce installation time.

RG59 cables are susceptible to interference if long cables are used. Due to this limitation, they are often used in closed circuit settings and for composite video signals. They are cheap and easy to set up, which makes them ideal for the job since CCTV cameras make use of lower frequency signals. Aside from CCTV cameras, they also see use in video projectors and some television systems.

RG6 cables have larger conducting wires than RG59 cables. This means they have higher bandwidth and can transfer more data faster. RG6 cables make use of aluminum foil shields and quad shielding. RG59 cables make use of copper shielding. So, RG6 cables have better shielding and so are less susceptible to outside interference. RG59 cables cannot transmit signals in the GHz frequency range due to their lower shielding but are very good at transmitting signals at 50 MHz or lower.

RG6 cables have less attenuation. So, these cables can be made longer without signal loss problems. RG59 cables have greater attenuation. RG59 cables cannot be made too long and are usually kept short to prevent loss during signal transmission.

RG6 cables are primarily used for satellite transmission cables and broadband internet connection due to their high bandwidth and great shielding. RG6 cables are more expensive than RG59 cables of the same length. This is because of the better shielding and thicker conductor.

The biggest deciding factor between these two cables is what you need the cable for. As you can see, there is very little to no overlap between their usages and no way you can substitute either of them for any purpose.

Similarly, RG6 cables struggle to carry lower frequency signals with good quality, and you will need to use RG59 cables for that. So, in the end, the most important thing you need to look at is what you need to use the cable for. Once you have the answer, picking the cable is easy. The RG6 cable Vs RG59 cable debate is thrown around a lot, but I believe this article has given you some insight into how simple the whole thing is. There are some key differences that help each cable perform differently.

Whenever you need to decide between the two, always recall what you need the particular cable for. Skip to content Coaxial cables are one of the most commonly used electrical cables.

What Are RG Cables? General Structure of RG Cables There is a general structure for the RG cables with differently rated cables having alterations to the structure. The general structure is: 1. Inner Conductor The first part of the cable is an inner conductor. Insulator Over the inner conductor, an insulator is used to cover it.

Shield Covering the insulator is a metal shield. Match up your cable to the conical end of the spacer and be sure that the second layer of aluminum shielding goes into the hole of the spacer while everything exterior to the aluminum shielding remains out of the hole. Push down on the cable with the spacer with a twisting motion to guarantee a nice separation between the layers. Remove the spacer from the cable and examine the cable.

Be careful not to hold the cable at the tip so that you will not disturb the space you have just created. You should clearly see a space between the layers as indicated by the brown arrow.

Pick out the connector you wish to attach to you cable. There are a variety of connectors you can choose from but the important factor is to make sure the connector you pick is compatible with both your cable and your video source. Before crimping your connector onto your cable. Make sure that the exposed cable is long enough to reach near the head of your connector. Match up the tip of your aluminum shield to the bottom of your connector head as shown with the dotted line.

Now make a mark on your cable at the same position as the end of your connector shown above as the brown arrow. This will help you indicate how far your cable should be inserted into the connector before crimping.

Now manually push your cable into the connector to your marked point. Now for crimping. You will be needing a crimping tool to connect your connector to the cable. Make sure that you crimping tool is of the right size for your connector. Insert your cable and connector into the crimping tool and press down on the handles.

You should feel resistance until the point where the colored rubber portion of your connector reduces to a line colored blue in this tutorial. Remove your crimping tool and give your connector a few good tugs to make sure it is on tight. Congratulations, your cable is now crimped and ready to perform to its optimum capacity. Now sit back and enjoy your quality video entertainment.